Teradek 10-0580 BEAM RX V Mount

$2,790.00
SKU:
TER-10-0580
UPC:
818264020104
Availability:
Ships from manufacturer
Shipping:
Calculated at Checkout
Manufacturer Part Number:
10-0580
reverb_sync:
off
  • Teradek 10-0580 BEAM RX V Mount

What's in the Box

  • Teradek Beam 3G-SDI Output Receiver
  • V Mount Battery Plate
  • 110-240V AC Power Adapter
  • 3x Receiver Antennas
  • Lightstand Adapter 1/4 20"
  • Thumb Screw
  • 1-Year Warranty

The Teradek Beam is a full HD camera-back H.264 encoder, capable of delivering stunning video at bit rates up to 30Mbps. Beam operates on the unlicensed 5GHz band and can transmit up to 2500' with just 2 frames of latency. Whether the job requires a wireless link back to the OB Van or an MPEG-TS stream back to the station, Beam gives broadcasters unparalleled flexibility in the field. This comes with 1 Beam RX with V mount, 3G-SDI Output and includes a dedicated bidirectional IFB channel.

Multicast Capable + IFB

Beam is multicast capable up to 4 receivers and includes a dedicated bidirectional IFB channel, which allows a news operations center to speak directly to the camera operator in the field.

Camera Control

Beam offers a full duplex RS-422 port for remotely controlling your camera.

Protocol Support

Beam utilizes the RTSP and MPEG-TS protocols, allowing broadcasters to transmit video over the Internet to a Beam decoder or directly to computers at very high bit rates. The Beam decoder can also act as an RTSP server, which will re-stream your video feed directly to a local computer.

Functional Design

With a 3G-SDI input and your choice of AB- or V-mount battery plates, Beam seamlessly integrates with all popular professional cameras. The chassis also includes an OLED screen for quick configuration, LAN port for broadcasting over wired networks and support for high power transmission on the 5.15 - 5.25GHz band.

Video Compression:H.264 Baseline Profile Level 4.2 with de-interlacing
System Latency:90 - 110 millisecond delay between Transmitter and Receiver
Wireless range:2500ft +- 200ft
Digital Video In/Out:3G-SDI
Video Port:SDI output
Supported Video Resolutions:SMPTE244: 480i59.94 (NTSC), 480i60 (861-D)
IEC61179-5: 576i50 (PAL)
SMPTE 296M: 720p23.98, 720p24, 720p25, 720p29.97, 720p30, 720p50, 720p59.94, 720p60
SMPTE 274M: 1080i50, 1080i59.94, 1080i60, 1080PsF23.98,1080PsF24, 1080PsF25, 1080PsF29.97, 1080PsF30, 1080p23.98, 1080p24, 1080p25, 1080p29.97, 1080p30, 1080p50, 1080p59.94, 1080p60
SDI Compliance:SMPTE 259M BI.656: SDTV Digital Signal/Data Serial Digital Interface
SMPTE 292M BT.1120: 1.5Gb/s Signal/Data Serial Digital Interface
SMPTE 425M: 3Gb/s Signal/Data Serial Digital Interface
SMPTE 299M: 16bit Digital Audio Format for SMPTE 292M
SMPTE 352M: Video Payload Identification for Digital Interfaces
Bitrate:RTSP Server: Up to 30Mbps
MPEG2-TS Server Up to 15Mbps
Main Digital Audio In/Out:SDI embedded audio: 48kHz 16-bit stereo linear PCM
Talk-Back Analog Audio In/Out:8kHz 16-bit stereo linear PCM with mini stereo phone input/output jack
Radio Power:Aggregate Power: 150mW (22dBm), 50mW (17dBm)/antenna
Radio standard:IEEE 802.11a/n: OFDM
Frequencies:U-NII-1 (5.15-5.25 GHz), U-NII-3 (5.725-5.85 GHz)
Antenna:3T x 3R MIMO, 3 antennas per WiMi6200TW/W1Mi6200RW
Security:802.1x, 802,11i, WPA2, WPA and WEP 64/128 TKIP 128bit AES
WPS:Wireless Protected Setup for easy set up and security configuration
Ethernet LAN:10/100 BASE-TX, RJ-45 jack
Multicast:Full duplex RS422 serial port
USB:Factory reset, IP configuration or firmware upgrade without PC
Power Input/Consumption:DC 7V-17V, 12 Watt
Operating Temperature:0 to 50 deg. C / 32 to 122 deg. F
Dimensions (H x W x D):Each board assembly (TX or RX): 170 x 105 x 28mm / 6.69 x 4.13 x 1.10"
Weight:610g / 21.52oz