What's in the Box
- 1 Beam Transmitter with AB Mount Battery Plate
- 1 Beam Receiver (with no mount)
The Teradek Beam Tx/Rx set comes with 1 Beam Transmitter and 1 Beam Receiver in an SKB Case.
1 Beam Transmitter with AB Mount Battery Plate
The Beam Tx has 3G-SDI Input, is a full HD camera-back H.264 encoder, capable of delivering stunning video at bit rates up to 50Mbps* using unlicensed 5GHz band with a range of 2500ft with just 2 frames of latency.
1 Beam Receiver (with no mount)
This set comes with 1 Beam Rx with 3G-SDI Output and includes a dedicated bidirectional IFB channel.
Beam is multicast capable to an unlimited number of Rx over LAN and to up to 4 receivers over WiFi.
BEAM Specification
Video Compression | H.264 Baseline Profile Level 4.2 with de-interlacing |
System Latency | 90 - 110 millisecond delay between Transmitter and Receiver |
Wireless range | 2500ft +- 200ft |
Digital Video In/Out | SD-SDI, HD-SDI, 3G-SDI |
Video Port | TX: SDI input and looped Output, RX: SDI output |
Supported Video Resolutions | SMPTE244 - 480i59.94 (NTSC), 480i60 (861-D) IEC61179-5 - 576i50 (PAL) SMPTE 296M - 720p23.98, 720p24, 720p25, 720p29.97, 720p30, 720p50, 720p59.94, 720p60 SMPTE 274M - 1080i50, 1080i59.94, 1080i60, 1080PsF23.98, 1080PsF24, 1080PsF25, 1080PsF29.97, 1080PsF30, 1080p23.98, 1080p24, 1080p25, 1080p29.97, 1080p30, 1080p50, 1080p59.94, 1080p60 |
SDI Compliance | SMPTE 259M BI.656 - SDTV Digital Signal/Data Serial Digital Interface SMPTE 292M BT.1120 - 1.5Gb/s Signal/Data Serial Digital Interface SMPTE 425M - 3Gb/s Signal/Data Serial Digital Interface SMPTE 299M - 16bit Digital Audio Format for SMPTE 292M SMPTE 352M - Video Payload Identification for Digital Interfaces |
Bitrate | RTSP Server - Up to 30Mbps MPEG2-TS Server - Up to 15Mbps |
Main Digital Audio In/Out | TX/RX - SDI embedded audio: 48kHz 16-bit stereo linear PCM |
Main Analog Audio Out | RX - 48kHz 16-bit stereo linear PCM with mini stereo phone output jack |
Talk-Back Analog Audio In/Out | RX/TX - 8kHz 16-bit stereo linear PCM with mini stereo phone input/output jack |
Radio Power | Aggregate Power: 150mW (22dBm), 50mW (17dBm)/antenna |
Radio standard | IEEE 802.11a/n: OFDM |
Frequencies | U-NII-1 (5.15-5.25 GHz) U-NII-3 (5.725-5.85 GHz) |
Antenna | 3T x 3R MIMO, 3 antennas per WiMi6200TW/W1Mi6200RW |
Security | 802.1x, 802,11i, WPA2, WPA and WEP 64/128 TKIP 128bit AES |
WPS | Wireless Protected Setup for easy set up and security configuration |
Ethernet LAN | 10/100 BASE-TX, RJ-45 jack |
Multicast | WiFi: Up to 4 Receivers LAN: No limit on number of receivers |
External Control | Full duplex RS422 serial port |
USB | Factory reset, IP configuration or firmware upgrade without PC |
Power Input/Consumption | DC 7V-17V, 12 Watt |
Dimensions | 170 x 105 x 28 each board assembly (TX or RX) |
Weight | TX: 2.2lbs. RX: 1.3 lbs. |
Operating Temperature | 32 deg F to 122 deg F 0 deg C to 50 deg C |