Sennheiser SL DI 4 XLR Dante interface

$1,374.95 $1,100.00
(You save $274.95)
Ships from manufacturer
Calculated at Checkout
Manufacturer Part Number:
  • Sennheiser SL DI 4 XLR Dante interface
  • Sennheiser SL DI 4 XLR Dante interface
  • Sennheiser SL DI 4 XLR Dante interface
  • Sennheiser SL DI 4 XLR Dante interface

Due to manufacturer's restrictions this item cannot be shipped outside of the United States.

What's in the Box

  • Sennheiser SL DI 4 XLR Four Input Dante Preamp and Interface
  • Sennheiser 2 Year Limited Warranty

The SL DI 4 XLR four input Dante preamp is the ideal interface for wireless microphone receivers and adding mic/line inputs to a Dante system. The small form factor to the SL DI 4 XLR allows them to be mounted almost anywhere, putting them close to audio sources and minimizing interference-prone analog wiring. The SL DI 4 XLR features four balanced mic/line inputs, each with software selectable +48V phantom power and 8 gain levels.

Front panel indicators show each channel's gain and phantom power status for easy troubleshooting. The SL DI 4 XLR has two network connections to allow Dante Daisy Chaining. Dante Daisy Chaining further simplifies system infrastructure wiring by allowing multiple SL DI 4 XLRs to use a single CAT 5 home run connection to a network switch. Power can also be daisy chained. The SL DI 4 XLR is powered by either external +12VDC or any PoE network switch. All adjustable parameters, like mic/ line gain and phantom power, are software controlled.

Sennheiser SL DI 4 XLR Features

  • XLR balanced and RF filtered mic/line inputs
  • Gain is individually adjustable per channel via software
  • 802.3af compliant PoE powered to work with any compliant PoE network switch, or an external +12VDC supply
  • +48V Phantom power - powers virtually all types of phantom
  • Powered microphones typically used in installed AV systems
  • Phantom power is switchable per channel via software
  • ID LED allows easy identification of the SL DI 4 XLR
  • Dante Daisy Chaining allows multiple SL DI 4 XLRs to beconnected over a single home-run to the Ethernet switch
  • Input Type:Balanced and RF filtered
    Gain:0 dB, +15 dB, + 30 dB, +45 dB, software selectable
    10 dB pad, software selectable
    Input Impedance:>1.8 kOhms at any gain
    Maximum Input Levels:+18 dBu at 0 dB gain, with pad
    +8 dBu at 0 dB gain, no pad
    -7 dBu at +15 dB gain, no pad-22 dBu at +30 dB gain, no pad
    -36 dBu at +45 dB gain, no pad
    Phantom Power:+48 V, 10 mAh per input, software selectable
    EIN:-113 dBu
    THD+N:<0.02 % at any gain
    Input signal 3 dB below maximum
    Frequency Response:20 Hz - 20 kHz
    Dante Network: Type:Standard Ethernet
    Dante Network: Connector:Single RJ-45
    Dante Network: Cable:Quality: Cat-5
    Dante Network: Transmission Speed:100 Mbps
    Dante Network: Daisy Chain:2 units when powered by 802.3af PoE
    3 units when powered by external +12 VDC power supply(Sennheiser NT 12-50CS)
    Power Requirements:Class 0 802.3af PoE PD compliant+12 VDC
    Power Consumption:2.7 W (225 mAh) at +12 VDC, no phantom power
    5.5 W (460 mAh) at +12 VDC, 10 mAh phantom power loadper input
    Operating Temperature:32 to 104 deg. F / 0 to 40 deg. C
    Dimensions (W x H x D):8.6 x 1.5 x 4.7" / 21.84 x 3.81 x 11.94cm
    Weight:1.7lbs / 0.77kg