**Due to restrictions, this item cannot be shipped outside of the United States.**
The DSQD/AES3 Half Rack Receiver with analog and digital Dante® network audio outputs utilizes the Lectrosonics signature digital architecture with remarkable audio quality and ultra-low latency. The receiver includes an extended operating range rivaling the best analog and Digital Hybrid Wireless® systems with continuously tunable tracking filters covering 470.100 - 614.375 MHz.
The DSQD/AES3 Receiver is a four-channel design with a host mainframe that contains the DSP, microprocessor,
antenna multicoupler and control interface. Antenna ports on the rear panel accept input from remote antennas, with a “loop-thru” output to another mainframe using the internal multicoupler. A kit is also available to mount antenna inputs (BNC connectors) on the front panel.
- Four-channel, half-rack design
- Continuously tunable tracking filters
covering 470.100 - 614.375 MHz
- Compatible with DSW, Duet and Digital Hybrid Wireless® transmitters
- Built-in wideband antenna multicoupler with loop-thru for additional receivers
- Antenna bias power enabled from the front panel (fused and over-temperature protected)
- IR bi-directional port for transmitter setup
- Analog and Dante® audio outputs with TalkBack (in applicable RX modes)
- Ethernet and USB interface
- Offline full-system frequency coordination
DSQD/AES3 Front Panel
Monitor any individual audio channel, or a stereo mix between pairs. Volume knob recesses into front panel.
LCD Control Panel
Easy navigation of all setup parameters is provided by a full color, backlit, LCD screen and membrane push
buttons. The high resolution display provides fantastic monitoring of all receiver parameters.
A bidirectional IrDA interface allows quick syncing of settings and encryption keys to transmitters with the
push of a button.
Easily interface to Wireless Designer or third-party software via the standard USB port, greatly accelerating
setup time and expanding system monitoring capabilities.
Two LEDs provide positive indication of antenna bias
DSQD/AES3 Rear Panel
Antenna inputs and outputs to an additional DSQD/AES3 allow “stacking” of up to three mainframes with a single pair of antennas.
Four full-size XLR jacks provide analog outputs.
Dante® Ethernet Ports
Dual Dante Ethernet ports provide the ability to daisy chain multiple DSQD/AES3s onto a Dante Audio Network.
AES3 Ports (DSQD/AES3/AES3 option)
AES3 outputs on two TA3M jacks (in place of the two Dante ports)
Easily interface to Wireless Designer or third-party software via the control Ethernet port, greatly accelerating setup time and expanding system monitoring capabilities.
Power Supply Input
The DSQD/AES3 is powered by 7 to 18 VDC from an external source capable of 2.5 amps.
|Operating Spectrum||470.100 - 614.375 MHz|
|Frequency Adjustment Range||25 kHz steps|
|Sampling Size and Rate||24-bit, 48 kHz|
|Digital Modulation||8PSK with Forward Error Correction|
|Data Encoding||Proprietary ADPCM|
(per FIPS 197 and FIPS 140-2)
|System Latency||Digital Output:
D2 mode: 0.75 ms plus Dante
Duet mode: 1.4 ms plus Dante
Hybrid modes: 2.0 ms plus Dante
D2 mode: 1.25 ms
Duet mode: 1.9 ms
Hybrid modes: 2.5 ms
|Audio Performance||Frequency Response: 20 Hz - 20 KHz, +\-1 dB
THD+N: 0.05% (1 KHz @ -10 dBFS)
Dynamic Range: 108 dB A-wtd, NR=NORMAL
Adjacent Channel Isolation: >85 dB
|Diversity Technique||Noiseless antenna switching|
|Sensitivity||-98 dBm for 10-5 BER|
|Antenna Inputs/Outputs||Dual BNC female, 50 ohm impedance|
|Audio Outputs:||XLR: Balanced, -35 to +8 dBu
Headphone: 1/4 inch phone jack
Dante model only: RJ45 Gigabit Ethernet
AES3 model only: TA3M
|External DC Power||7 to 18 VDC; 2.5A (max)|
|Weight||1.95 lbs.; 880 grams|
|Dimensions||8.375 x 1.75 x 7.375 in.
213 x 44.5 x 187 mm.